新聞中心

        EEPW首頁 > 模擬技術 > 設計應用 > 使用寬帶電壓和電流反饋運算放大器時的應用基礎

        使用寬帶電壓和電流反饋運算放大器時的應用基礎

        作者: 時間:2013-11-13 來源:網絡 收藏
        : 0px; -webkit-text-size-adjust: auto; -webkit-text-stroke-width: 0px">With both current and voltage feedback operational amplifiers (op amp) available to the system designer, how do you decide which one to use? This article is the second of two parts. It reviews several applications that are most suitable to the current feedback type, then it introduces the fully differential amplifier (FDA). All applications covered in Part 1 for voltage feedback op amps are also suitable for an FDA, but some particularly useful applications for this type of amplifier are shown here.

        Keep in mind that applications requiring flexibility in the gain setting network will benefit from the gain bandwidth independence of the current feedback (CFB) design. As described inPart 1, the loop gain equation for a CFB includes only the feedback impedance while the gain element can be varied freely with minimal bandwidth interaction. The following examples exploit that advantage in several situations where a CFB would be the preferred solution.

        Example A
        If an inverting summing amplifier is required with a signal bandwidth that is independent of the number of channels summed or the required gains in those channels, a CFB amplifier should be used.Figure 1shows an example of this approach using the high output voltage and current THS3091.


        (Click to Enlarge Image)
        Figure 1. Inverting summing amplifier using the high voltage/current THS3091.


        Here, we assume a 0 Ω source for each of the signal sources where each channel would see a gain of "2 V/V. For these CFB designs, the feedback resistor is first picked to be close to the recommended value for that particular CFB amplifier. Then, each input resistor should be selected according to the gain required by that channel.

        Recall that this circuit implemented with a voltage feedback (VFB) has a bandwidth set by the noise gain (NG). For instance, five channels summed with a gain of -2 V/V will have a noise gain of 11. This condition would set a bandwidth for all five channels reduced to the [gain bandwidth product (GBP)]/11 even though each signal only sees a gain of -2 V/V. Using a CFB for this application retains the bandwidth much better because the parallel combination of all gain resistors does not enter strongly into the loop gain equation.

        By way of comparison,Figure 2simulates a single channel of Figure 1 using first the CFB TH3091, then a similar VFB THS4031. The THS4031 is a low-noise, high-voltage VFB that offers approximately 200 MHz GBP.


        (Click to Enlarge Image)
        Figure 2. Comparative frequency response for one channel of Figure 1 using THS3091 and THS4031.


        The circuit of Figure 1 produces a noise gain of 11, which shows up as a signal bandwidth close to 18 MHz for the THS4031, while the THS3091 gives about 200 MHz for each channel.



        關鍵詞: 寬帶電壓 電流反饋 運算放大器

        評論


        相關推薦

        技術專區

        關閉
        主站蜘蛛池模板: 张家口市| 卢氏县| 淮安市| 馆陶县| 台州市| 阜平县| 德保县| 汉沽区| 礼泉县| 平遥县| 凤凰县| 蒙山县| 九龙坡区| 平罗县| 涿州市| 资讯 | 思茅市| 高淳县| 吉首市| 凭祥市| 神农架林区| 贡嘎县| 陇西县| 达日县| 德庆县| 安阳县| 扎兰屯市| 宜兰市| 随州市| 平陆县| 比如县| 满城县| 临沭县| 温泉县| 延寿县| 灵川县| 靖州| 晋州市| 铜山县| 微山县| 蓝山县|