步進電機定位控制系統VHDL程序與仿真

步進電機定位控制系統VHDL程序與仿真
library IEEE;
use IEEE.std_logic_1164.all;
use IEEE.std_logic_arith.all;
use IEEE.std_logic_unsigned.all;
entity step_motor is
port (reset:in STD_LOGIC; --系統復位信號
dir: in STD_LOGIC; --方向控制信號
clk: in STD_LOGIC; --系統時鐘信號
ini: in STD_LOGIC; --初始化使能信號
manner: in STD_LOGIC_VECTOR (1 downto 0); --激磁方式的選擇開關
angle: in INTEGER range 255 downto 0; --步進角的倍數設定輸入
baBA: out STD_LOGIC_VECTOR (3 downto 0)); --步進電機狀態輸出
end step_motor;
architecture stepmotor_arch of step_motor is
signal count: INTEGER range 0 to 7; --計數器
signal cntInc: INTEGER range -2 to 2; --設定累加器所需的累（加/減）計數值
signal cc : integer range 0 to 3;
signal cntIni: INTEGER range -1 to 0; --設定累加器所需的計數初值
signal angleDnCount: INTEGER range 255 downto 0; --計算已經轉過的步進角
signal angleDnCntDec: INTEGER range 2 downto 1;
begin
process(dir, manner, angle)--, ini)
begin
--if ini='1' then
cc=conv_integer(manner);
if dir='0' then
case cc is
when 1 => -- 1-?相激勵
--count=0;
cntIni=0;
cntInc=2;
angleDnCntDec=2;--10;
when 2 => -- 2-?相激勵
--count=7;
cntIni=-1;
cntInc=2;
angleDnCntDec=2;--10;
when 3 => -- 1-2?相激勵
--count=0;
cntIni=0;
cntInc=1;
angleDnCntDec=1;--01;
when 0 => --manner=00 autodetect
if (angle rem 2) =1 then -- 2-?相激勵
--count=7;
cntIni=-1;
cntInc=2;
angleDnCntDec=2;--10;
else -- 1-?相激勵
--count=0;
cntIni=0;
cntInc=2;
angleDnCntDec=2;--10;
end if; --angle
end case; --manner
else -- if dir='1'
case cc is
when 1 => -- 1-?相激勵
--count=0;
cntIni=0;
cntInc=-2;
angleDnCntDec=2;--10;
when 2 => -- 2-?相激勵
--count=7;
cntIni=-1;
cntInc=-2;
angleDnCntDec=2;--10;
when 3 => -- 1-2?相激勵
--count=0;
cntIni=0;
cntInc=-1;
angleDnCntDec=1;--01;
when 0 => --manner=00 autodetect
if (angle rem 2) = 1 then -- 2-?相激勵
cntIni=-1;
cntInc=-2;
angleDnCntDec=2;--10;
else -- 1-?相激勵
cntIni=0;
cntInc=-2;
angleDnCntDec=2;--10;
end if; --angle
end case; --manner
end if; -- else dir=0
--end if; -- ini
end process;
counting_reset: process(reset,ini, angle, clk)
begin
if reset='1' then
count=0;
angleDnCount=0;
elsif clk'event and clk='1' then
if ini='0' then
count=0+cntIni;
angleDnCount=angle;
else
count = count+cntInc;
if angleDnCount > angleDnCntDec then
angleDnCount = angleDnCount-angleDnCntDec;
else
angleDnCount = 0;
end if;
end if;
end if;
end process;

baBA =0000 when angleDnCount=0 else
0001 when count=0 else
0011 when count=1 else
0010 when count=2 else
0110 when count=3 else
0100 when count=4 else
1100 when count=5 else
1000 when count=6 else
1001;-- when count>=7;
end stepmotor_arch;