新聞中心

        EEPW首頁 > 嵌入式系統 > 設計應用 > 基于POWR1220AT8設計的12V熱插拔技術

        基于POWR1220AT8設計的12V熱插拔技術

        作者: 時間:2010-06-22 來源:網絡 收藏
        ispPAC-集成了在系統可編程邏輯和在系統可編程模擬功能,是通用的電源監視器,順序和余量控制器,它提供12個單獨的模擬輸入通道,用來監視多達12個電源測試點. 提供和IPMC標準的命令接口,能把板上的DC/DC轉換器轉換成精密的數控電源.本文介紹了ispPAC-主要特性,方框圖,以及應用方框圖, 評估板外形圖,采用ispPAC-POWR1220AT8的熱插拔控制器參考電路圖.


        ispPAC-POWR1220AT8典型應用:

        The Power Manager II POWR1220AT8 provides a standard command interface to the IPMC while performing FRU specific payload power management functions using the on-chip CPLD. The POWR1220AT8 also converts all on board DC-DC converters into accurate digitally controlled supplies.


        圖1.ispPAC-POWR1220AT8方框圖

        圖2.ispPAC-POWR1220AT8應用方框圖

        圖3.ispPAC-POWR1220AT8提高DC/DC轉換器精度的應用方框圖

        The PAC-POWR1220AT8 evaluation board allows the designer to quickly configure and evaluate the ispPAC-POWR1220AT8 device on a fully assembled printed-circuit board. The four-layer board supports a 100-pin TQFP package, pads for user I/O, a JTAG programming cable connector, and a connector for the device’s I2C interface. JTAG programming signals can be generated by using an ispDOWNLOAD® programming cable connected between the evaluation board and a PC. Both analog and digital features of the ispPACPOWR1220AT8 device can be easily configured using PAC-Designer® software.

        The PAC-POWR1220AT8 evaluation board is available in a Development Kit that includes:

        PAC-POWR1220AT8 Evaluation Board

        ispDOWNLOAD Cable

        AC Adapter (International plugs)

        User Documentation

        圖4.ispPAC-POWR1220AT8評估板外形圖

        采用ispPAC-POWR1220AT8的熱插拔控制器參考

        A hot swap controller is used to limit the inrush current when a circuit board is plugged into a powered backplane.

        In addition, a hot swap controller may offer some or all of the following features: over-current protection (electronic circuit breaker), over-voltage protection, and under-voltage protection. Hot swap controllers are also required to isolate the board from the backplane which is useful in troubleshooting, maintenance, and upgrade activities. The power-down request may come from the backplane (remote) or an on-board switch (manual).

        This document describes how a Lattice Power Manager II ispPAC®-POWR1220AT8 can be used to implement the functions required for hot swap applications. This reference design is targeted to operate on the Power Manager Hercules Development Kit (PAC-POWR1220AT8-HS-EVN C Standard or PAC-POWR1220AT8-HA-EVN CAdvanced).

        上一頁 1 2 下一頁

        評論


        相關推薦

        技術專區

        關閉
        主站蜘蛛池模板: 永城市| 云林县| 天柱县| 抚州市| 北海市| 中江县| 深泽县| 新平| 监利县| 辽阳县| 沅江市| 金沙县| 任丘市| 汶上县| 乳山市| 随州市| 天等县| 新营市| 酉阳| 庆城县| 同德县| 大关县| 东兰县| 定陶县| 双牌县| 高要市| 西乌珠穆沁旗| 汕头市| 长泰县| 东光县| 广宁县| 嘉荫县| 南溪县| 平原县| 焉耆| 南岸区| 福清市| 江永县| 永登县| 南开区| 霍林郭勒市|