新聞中心

        EEPW首頁 > 模擬技術 > 設計應用 > 可處理76V電壓的斷路器,Circuit Breaker H

        可處理76V電壓的斷路器,Circuit Breaker H

        作者: 時間:2011-05-19 來源:網絡 收藏

        Abstract: A current-sense amplifier, comparator, external CMOS switch, and an external transistor can be used to create a circuit breaker.

        The simplicity of low-side current monitoring can mask the advantages of a high-side approach. You can monitor load currents in a power supply, a motor driver, or another power circuit on either the high or the low side (ground). However, you should not let the ease of low-side monitoring cause you either to overlook its dangers or the advantages of a high-side approach.

        Various fault conditions can bypass the low-side monitor, thereby subjecting the load to dangerous and undetected stresses. However, a high-side monitor connected directly to the power source can detect any downstream failure and trigger the appropriate corrective action. Traditionally, such high-side monitors required a precision op amp, a boost power supply to accommodate the op amp's limited common-mode range, and some precision resistors. Now, the MAX4080 IC can sense high-side currents in the presence of common-mode voltages as high as 76V (Figure 1).

        In this application circuit the MAX4080, IC1, provides a ground-referenced voltage-source output proportional to the high-side current of interest. This output voltage is proportional to the voltage across an external sense resistor multiplied by five.

        可處理76V電壓的斷路器,Circuit Breaker H
        Figure 1. A current sense amplifier, comparator, and a few external components form a low-cost circuit breaker.

        IC1, IC2, and a few external parts form a low-cost circuit breaker. RSENSE senses load currents, and Q1 controls the currents. The design accepts inputs of 4.5V to 76V. The initial application of VIN and VDD places the breaker in its trip state. Pressing S1 resets the breaker and connects power to the load and IC1, thereby activating Q1. When the voltage across RSENSE is multiplied by five and exceeds 1.2V, then IC2 outputs a low signal on COUT which turns off Q2 and Q1. Press S1 to reset the breaker.

        Reprinted from EDN Magazine May 25, 2000.

        斷路器相關文章:斷路器原理


        高壓真空斷路器相關文章:高壓真空斷路器原理
        漏電斷路器相關文章:漏電斷路器原理


        評論


        相關推薦

        技術專區

        關閉
        主站蜘蛛池模板: 新野县| 朔州市| 徐水县| 商河县| 土默特左旗| 石楼县| 钟山县| 留坝县| 微博| 宜黄县| 蓬莱市| 永登县| 裕民县| 天镇县| 驻马店市| 广安市| 嘉禾县| 无棣县| 宁海县| 昌平区| 琼结县| 曲阜市| 平定县| 凤冈县| 芦溪县| 游戏| 成武县| 北辰区| 哈尔滨市| 策勒县| 泰州市| 南开区| 孝感市| 五原县| 进贤县| 正阳县| 林州市| 隆回县| 诸城市| 靖西县| 新兴县|