通過MSP430的IO口模擬I2C總線對AT24C25進行讀寫程序

一、微處理器的兩個模擬I/O口在和SDA,SCL連接時必須使用上拉電阻。

一、I2C總線空閑的時候，兩條信號線應該維持高電平。否則，上拉電阻上會有耗電。特別是在上電過程中，I/O線上電平也應保持在高電平狀態。也就是說：當Master的I2C使用的是I/O軟件模擬時，一定要保證該兩個I/O上電默認均為輸入（或高阻）或者輸出高電平，切不可默認為輸出低電平。I/O默認為輸入時，可以通過外部上拉電阻將I2C信號線拉至高電平。

該程序通過調試，可以直接應用，程序如下：

文 件 名 : AT24C256.S43.C

* 功能描述 : I/O模擬I2C時序讀寫AT24CXX(支持字節寫、頁寫、字節讀、順序讀)
* 作 者 : 夢回大唐

* 創建日期 : 2011-4-18

* 版 本 : Version1.0
*************************************************************************************************/

#include
#define SDA_INP5DIR &=~BIT0// P5.0 IN
#define SDA_OUTP5DIR |=BIT0// P5.0 OUT

#define SDA_LOWP5OUT &=~BIT0// sda=0
#define SDA_HIGHP5OUT |=BIT0// sda=1

#define SCL_INP5DIR &=~BIT1// P5.1 IN
#define SCL_OUTP5DIR |=BIT1// P5.1 OUT

#define SCL_LOWP5OUT &=~BIT1
#define SCL_HIGHP5OUT |=BIT1
#defineW_EEPROM_LENGH14

#defineTURE1
#defineFALSE0
#defineAckError0x55
#defineOutOfRang0xaa
#defineOutOfAddr0xbb

unsigned chardat[W_EEPROM_LENGH]={1,2,3,4,5,6,7,8,9,10,11,12,13,14};
unsigned charx[W_EEPROM_LENGH];

void i2c_delay(unsigned char us);
void i2c_delay_ms(unsigned char ms);
void i2c_start();
void i2c_stop(void);
void i2c_SendAck(void);
void i2c_SendNoAck(void);
unsigned char i2c_check_ACK(void);
void i2c_SendByte(unsigned char data);
unsigned char i2c_RevByte(void);
unsigned char EEPROM_ByteWrite(unsigned int addr,unsigned char data);
unsigned char EEPROM_RandomRead(unsigned int addr);
unsigned char EEPROM_SequentialRead(unsigned int addr,unsigned int n,unsigned char* p);
unsigned int EEPROM_PageWrite(unsigned int page,unsigned char* p,unsigned char n);

void i2c_delay(unsigned char us)
{
unsigned char tmp;
while(us--)
{
for(tmp=0;tmp<4;tmp++)
{
_NOP();
}
}
}

void i2c_delay_ms(unsigned char ms)
{
unsigned int tmp;
while(ms--)
{
for(tmp=0;tmp<5000;tmp++)
{
_NOP();
}
}

}

void i2c_start(void)
{
SDA_OUT;
i2c_delay(20);
SDA_HIGH;
i2c_delay(3);
SCL_HIGH;
i2c_delay(2);
SDA_LOW;
i2c_delay(5);
SCL_LOW;
i2c_delay(10);
}

void i2c_stop(void)
{
SDA_OUT;
SDA_LOW;
i2c_delay(2);
SCL_HIGH;
i2c_delay(2);
SDA_LOW;
i2c_delay(2);
SDA_HIGH;
}

void i2c_SendAck(void)
{
SDA_OUT;
SDA_LOW;
i2c_delay(2);
SCL_LOW;
i2c_delay(2);
SCL_HIGH;
i2c_delay(2);
SCL_LOW;
SDA_HIGH;
}

void i2c_SendNoAck(void)
{
SDA_OUT;
SDA_HIGH;
i2c_delay(2);
SCL_LOW;
i2c_delay(2);
SCL_HIGH;
i2c_delay(2);
SCL_LOW;
}

unsigned char i2c_check_ACK(void)
{
unsigned char AckStatus;
SDA_IN;
SCL_HIGH;
i2c_delay(2);
if(P5IN & 0x01)
{
AckStatus = FALSE;
}
else
{
AckStatus = TURE;
}
SCL_LOW;
i2c_delay(2);
SDA_OUT;
return AckStatus;
}

void i2c_SendByte(unsigned char data)
{
unsigned char tmp;
SDA_OUT;
for(tmp=0;tmp<8;tmp++)
{
if(data & 0x80)
{
SDA_HIGH;
}
else
{
SDA_LOW;
}
i2c_delay(2);
SCL_HIGH;
i2c_delay(2);
SCL_LOW;
i2c_delay(2);
data <<= 1;
}
i2c_delay(15);
}

unsigned char i2c_RevByte(void)
{
unsigned char tmp;
unsigned char DATA=0;
SDA_IN;
SCL_LOW;
i2c_delay(2);
for(tmp=0;tmp<8;tmp++)
{
SCL_HIGH;
i2c_delay(2);
DATA <<= 1;
if(P5IN & 0x01)
{
DATA |= 0x01;
}
else
{
DATA &= 0xfe;
}
SCL_LOW;
}
SDA_OUT;
return DATA;
}