STM32F107VCT6的通用定時器的輸入捕獲功能配置

#define NVIC_Priority_Timer4 1

void TIM4_Init_Config(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
TIM_ICInitTypeDef TIM_ICInitStructure; //輸入捕獲結構體
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure; //時基結構體

RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD, ENABLE);

/*
*PD15-TIM4_Ch4 矩形方波的輸入管腳
*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_15;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOD, &GPIO_InitStructure);

GPIO_PinRemapConfig(GPIO_Remap_TIM4 , ENABLE); //TIM4_CH4/PD15 硬件已經映射好的，不能將TIM4_CH4用于其他管腳

NVIC_InitStructure.NVIC_IRQChannel = TIM4_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = NVIC_Priority_Timer4;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 4;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);

/*

* 設置TIM4的時基：(1+TIM_Prescaler )/72M)*(1+TIM_Period )=((1+0xFFFF)/72M)*(1+71) = 65536/1M

* （定時器計滿16位用時，則計一個數用時1/1M）

*/
TIM_TimeBaseStructure.TIM_Period = 0xFFFF;
TIM_TimeBaseStructure.TIM_Prescaler = 71;
TIM_TimeBaseStructure.TIM_ClockDivision = 0x0;
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
TIM_TimeBaseInit(TIM4, &TIM_TimeBaseStructure);

TIM_ICInitStructure.TIM_Channel = TIM_Channel_4;
TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Falling; //PD15管腳檢測下降沿
TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI;
TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1;
TIM_ICInitStructure.TIM_ICFilter = 0xF;
TIM_ICInit(TIM4, &TIM_ICInitStructure);

TIM_Cmd(TIM4, ENABLE);
TIM_ITConfig(TIM4, TIM_IT_CC4, ENABLE);
}

unsigned int IC4ReadValue1 = 0;
unsigned int IC4ReadValue2 = 0;
unsigned int CaptureNumber_ch4 = 0;
unsigned int Capture_ch4 = 0;

void TIM4_IRQHandler(void)
{
//每當PD15管腳檢測到下降沿，就會進入到該中斷處理函數
if (TIM_GetITStatus(TIM4, TIM_IT_CC4) == SET)
{

TIM_ClearITPendingBit(TIM4, TIM_IT_CC4);

if (CaptureNumber_ch4 == 0)
{

CaptureNumber_ch4 = 1;
IC4ReadValue1 = TIM_GetCapture4(TIM4);
}
else if (CaptureNumber_ch4 == 1)
{

CaptureNumber_ch4 = 0;
IC4ReadValue2 = TIM_GetCapture4(TIM4);
if (IC4ReadValue2 > IC4ReadValue1)
{
Capture_ch4 = (IC4ReadValue2 - IC4ReadValue1);
}
else if (IC4ReadValue2 < IC4ReadValue1)
{
Capture_ch4 = ((0xFFFF - IC4ReadValue1) + IC4ReadValue2);
}
else
{
Capture_ch4 = 0;
}
}

}
}