Powerint LNK460KG 20W LED驅動方案

Powerint公司的LinkSwitch-PL系列產品集成了725V功率MOSFET,間斷模式可變頻率可變開態時間控制器,頻率抖動器,逐個周期的限流和滯后熱關斷等功能,具有高效率和高功率因素,它的控制算法提供無閃爍TRIAC調光,而外接元件最少.本文介紹了LNK460KG產品亮點,方框圖,典型應用電路,替代A19白熾燈5W 15V LED驅動電路圖以及20W LED驅動演示板主要特性和指標,電路圖,材料清單和PCB元件布局圖.

High Efficiency (>90%), High Power Factor (>0.97), Low A-THD (15%), 20 W Output Non-Isolated Buck LED Driver Using LinkSwitchTMPL LNK460KGHigh Efficiency (>90%), High Power Factor (>0.97), Low A-THD (15%), 20 W Output Non-Isolated Buck LED Driver Using LinkSwitchTMPL LNK460KG

The LinkSwitch-PL family enables a very small and low cost single-stage power factor corrected constant current driver for solid state lighting. Optimized for direct LED current sensing, the LinkSwitch-PL operates over a wide input voltage range dELivering an output power of up to 16 W. The LinkSwitch-PL control algorithm provides flicker-free TRIAC dimming with minimal external components.

Each device incorporates a 725 V rated power MOSFET, a novel discontinuous mode variable frequency variable on-time controller, frequency jitter, cycle by cycle current limit and hysteretic thermal shutdown in a monolithic 4-pin IC, available in SO-8C, eSOP-12, and eDIP-12 packages.

圖1.LNK460KG方框圖

圖2.LNK460KG典型應用電路圖

圖2.替代A19白熾燈5W 15V LED驅動電路圖

20W LED驅動演示板

The document describes a non-isolated, high efficiency, high power factor (PF) LED driver designed to drive a nominal LED string voltage of 85 V at 240 mA from an input voltage range of 195 VAC to 265 VAC (47 Hz – 63 Hz). The LED driver utilizes the LNK460KG from the LinkSwitch-PL family of ICs.

The topology used is a single-stage non-isolated buck that meets the stringent space and efficiency requirements for this design. LinkSwitch-PL based designs provide high power factor (>0.9) meeting international requirements.

This document contains the LED driver specification, schematic, PCB details, bill of materials, transformer documentation and typical performance characteristics.

20W LED驅動演示板主要特性:

Low cost, low component count (29 parts), small size (height 8 mm), and single-sided PCB

Single-stage power factor correction and constant current (CC) output

Highly energy efficient, >90%

Integrated protection and reliability features

Output short-circuit protection with auto-recovery

Auto-recovering thermal shutdown with hysteresis

No damage during brown-out conditions

PF >0.97, % ATHD 15% at nominal 230 VAC input

Easily meets Class C harmonic requirement (>25 W) even with multiple tubes in parallel operation

Meets 1 kV differential line surge and EN55015 conducted EMI

圖3.20W LED驅動演示板外形圖

20W LED驅動演示板主要指標:

圖4.20W LED驅動演示板電路圖

20W LED驅動演示板材料清單(BOM):

圖5.20W LED驅動演示板元件布局圖