51單片機矩陣鍵盤與左右流水燈控制C程序

hex文件及其工程文件下載：http://www.51hei.com/f/jzzyou.rar 以下是測試ok的源代碼：

/*
*功能：使用矩陣按鍵使得按鍵按下時數碼管上顯示各自對應的數字的平方數；
* 且使用定時器0中斷使得彩色流水燈先以20毫秒的速度左移流動4秒后，
* 然后使得彩色流水燈以20毫秒的速度右移流動；
*日期：2013-05-02-16:46
*作者：徐冉
*特別說明：本程序代碼已經通過調試，僅供學習使用；
*
*/
/***********AT89C52-RC單片機- 51hei-5 實驗板***********/
/*****************51hei開發板*********************/
#include
typedef unsigned int uint;
typedef unsigned char uchar;
sbit wela = P2^7;
sbit dula = P2^6;
sbit FM = P2^3;
uchar code table[] = {
0x3F, //"0"
0x06, //"1"
0x5B, //"2"
0x4F, //"3"
0x66, //"4"
0x6D, //"5"
0x7D, //"6"
0x07, //"7"
0x7F, //"8"
0x6F //"9"
};
uint key1 = 0;
uchar counter = 0, x = 0, flag = 0;
void display(uint num);
void delay(uint xms);
void Marix_keyscan();
void init();
//主程序
void main()
{
init();//定時器0初始化
while(1)
{
if(counter == 200)//定時器定時左移流動4秒
{
counter = 0;
flag= 1;
TR0 = 0;
TH0 = 0xB8;
TL0 = 0X00;
TR0 = 1;
x = 0;
}
Marix_keyscan();
display(key1);
}
}
//定時器0初始化子程序
void init()
{
TMOD = 0x01;
TH0 = 0xB8;
TL0 = 0X00;
EA = 1;
ET0 = 1;
TR0 = 1;
}
//數碼管優化顯示子程序
void display(uint num)
{
uchar bai, shi, ge;
bai = num / 100 % 10;
shi = num / 10 % 10;
ge = num % 10;
if(num < 10)
{
dula = 1;
P0 = table[ge];
dula = 0;
P0 = 0xff;
wela = 1;
P0 = 0xfe;
wela = 0;
P0 = 0x00;
delay(1);
}
else if(num < 100)
{
dula = 1;
P0 = table[shi];
dula = 0;
P0 = 0xff;
wela = 1;
P0 = 0xfe;
wela = 0;
P0 = 0x00;
delay(1);
dula = 1;
P0 = table[ge];
dula = 0;
P0 = 0xff;
wela = 1;
P0 = 0xfd;
wela = 0;
P0 = 0x00;
delay(1);
}
else
{
dula = 1;
P0 = table[bai];
dula = 0;
P0 = 0xff;
wela = 1;
P0 = 0xfe;
wela = 0;
P0 = 0x00;
delay(1);
dula = 1;
P0 = table[shi];
dula = 0;
P0 = 0xff;
wela = 1;
P0 = 0xfd;
wela = 0;
P0 = 0x00;
delay(1);
dula = 1;
P0 = table[ge];
dula = 0;
P0 = 0xff;
wela = 1;
P0 = 0xfb;
wela = 0;
P0 = 0x00;
delay(1);
}
}
//延時子程序
void delay(uint xms)
{
uint i, j;
for(i = xms; i > 0; i--)
for(j = 125; j > 0; j--);
}
//矩陣按鍵檢測子程序
void Marix_keyscan()
{
uchar temp; //定義一個變量存放P3口的值
//第一次矩陣按鍵檢測
P3 = 0xfe; //給P3口賦一個值，使得矩陣按鍵的第一行置為低電平，其余口置為高電平；
temp = P3; //將P3口的值賦給temp
temp &= 0xf0; //通過與0xf0&來檢測矩陣按鍵的各列通過行列檢測與檢測矩陣按鍵
if(temp != 0xf0)
{
//檢測有矩陣按鍵按下
delay(5);//消抖
temp = P3;//再次將P3口的值賦給temp,即再次賦初值檢測矩陣按鍵；
temp &= 0xf0; //再次按位與檢測矩陣按鍵行列
if(temp != 0xf0)
{ //確認有鍵按下
FM = 0;//蜂鳴器發聲
temp = P3; //將此時的P3口的值賦給temp
switch(temp)
{
case 0xee: key1 = 1 * 1;
break; //檢測到key1按下
case 0xde: key1 = 2 * 2;
break; //檢測到key2按下
case 0xbe: key1 = 3 * 3;
break; //檢測到key3按下
case 0x7e: key1 = 4 * 4;
break; //檢測到key4按下
default:
break;
}
//按鍵釋放
while(temp != 0xf0)
{
//重新賦初值檢測矩陣按鍵
temp = P3;
temp &= 0xf0;
}
delay(5);//釋放去抖
//按鍵釋放
while(temp != 0xf0)
{
//重新賦初值檢測矩陣按鍵
temp = P3;
temp &= 0xf0;
}
//按鍵釋放關閉蜂鳴器
FM = 1;
}
}