Stm32RS485串口通信——中斷接收發送數據

/**說明：*PA9:USART1_TX;PA10:USART1_RX*/#include "stm32f10x.h"#include "stm32f10x_rcc.h"#include "stm32f10x_gpio.h"#include "stm32f10x_usart.h"#include "stm32f10x_exti.h"#include "system_stm32f10x.h"#include "misc.h"void RCC_Configuration(void);void GPIO_Configuration(void); void USART_Configuration(void);void NVIC_Configuration(void);int main(){SystemInit();//72mRCC_Configuration();GPIO_Configuration(); USART_Configuration();NVIC_Configuration();GPIO_ResetBits(GPIOE,GPIO_Pin_5);                                              while(1);}void RCC_Configuration(void)  {   RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOE|RCC_APB2Periph_AFIO,ENABLE);  RCC_APB1PeriphClockCmd(RCC_APB2Periph_USART1,ENABLE);} void GPIO_Configuration(void)  {  GPIO_InitTypeDef GPIO_InitStructure; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;             //CS_485GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;      //推挽輸出GPIO_Init(GPIOE, &GPIO_InitStructure);   GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;             //管腳2GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;       //復用推挽輸出GPIO_Init(GPIOA, &GPIO_InitStructure);                //TX初始化GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;             //管腳3GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING; //浮空輸入        GPIO_Init(GPIOA, &GPIO_InitStructure);                //RX初始化} void USART_Configuration(void)//串口初始化函數{//串口參數初始化  USART_InitTypeDef USART_InitStructure;               //串口設置恢復默認參數//初始化參數設置USART_InitStructure.USART_BaudRate = 9600;                  //波特率9600USART_InitStructure.USART_WordLength = USART_WordLength_8b; //字長8位USART_InitStructure.USART_StopBits = USART_StopBits_1;      //1位停止字節USART_InitStructure.USART_Parity = USART_Parity_No;         //無奇偶校驗USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//無流控制USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;//打開Rx接收和Tx發送功能USART_Init(USART2,&USART_InitStructure);                   //初始化USART_ITConfig(USART2,USART_IT_TXE,ENABLE);                //允許串口1發送中斷。USART_ITConfig(USART2,USART_IT_RXNE,ENABLE);               //允許串口1接收中斷。USART_Cmd(USART2,ENABLE);                                  //啟動串口USART_ClearFlag(USART2,USART_FLAG_TC);                     //發送完成標志位} void NVIC_Configuration(void)//配置中斷優先級  {  NVIC_InitTypeDef NVIC_InitStructure;  NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);  NVIC_InitStructure.NVIC_IRQChannel = USART2_IRQn;  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;  NVIC_Init(&NVIC_InitStructure);  }  

#include "..includestm32f10x.h" #include "..includestm32f10x_it.h"#include "..includestm32f10x_gpio.h"#include "..includestm32f10x_usart.h"void delay_ms(u16 time)     {    u16 i=0;    while(time--)     {    i=12000;    while(i--);    }    } void USART2_IRQHandler(void){u8 RX_dat;if(USART_GetITStatus(USART2,USART_IT_RXNE)==SET)//USART_IT_RXNE：接收中斷{ RX_dat=USART_ReceiveData(USART2);    GPIO_SetBits(GPIOE,GPIO_Pin_5);delay_ms(1);USART_SendData(USART2,RX_dat);   while(USART_GetFlagStatus(USART2,USART_FLAG_TXE) == RESET){} //發送數據寄存器空標志位delay_ms(2);GPIO_ResetBits(GPIOE,GPIO_Pin_5);}   }